stm32
steps I took to get stm32nucleo mb1136 C-03 running in Arduion IDE on OSX 10.10 Yosemite
- no soldering/desoldering needed in my case.
- install Arduino 1.6.5 (don't use 1.6.6 or 1.6.7 because of [[https://github.com/rogerclarkmelbourne/Arduino_STM32/issues/147|errors]])
- tools -> board -> board manager... -> install 'Arduino Due'
- download [[https://github.com/rogerclarkmelbourne/Arduino_STM32/archive/master.zip|Arduino_STM32]]
- unpack to ~/Documents/Arduino/hardware/Arduino_STM32
- Install libusb from http://rudix.org/packages/libusb.html (in case of upload errors)
- restart Arduino IDE
- select tools -> board -> STM Nucleo F103RB (STLink)
- select tools -> port -> usbserial or usbmodem1234
- load Blink example
- upload Blink example
- to communicate with Serial Monitor in the Arduino IDE I had to use Serial1 (instead of just Serial). ([[http://stm32duino.com/viewtopic.php?f=3&t=512&start=20|more info]])
pins
(::stm-nucleo-pins.jpg?direct&700|)
resources
- http://www.st.com/web/catalog/tools/FM116/SC959/SS1532/LN1847/PF259875?icmp=nucleo-ipf_pron_pr-nucleo_feb2014&sc=nucleoF103RB-pr
- https://developer.mbed.org/platforms/ST-Nucleo-F103RB/
- http://www.stm32duino.com/
- https://www.youtube.com/watch?v=-zwGnytGT8M
- https://github.com/rogerclarkmelbourne/Arduino_STM32
- https://github.com/rogerclarkmelbourne/Arduino_STM32/wiki/Installation
- [[http://www.stm32duino.com/viewtopic.php?t=248|problems with nucleo with arduino ide]]
- http://www.stm32duino.com/viewforum.php?f=29
- http://www.rogerclark.net/
- http://www.st.com/web/en/resource/technical/document/user_manual/DM00105823.pdf
read the docs
- [[https://github.com/rogerclarkmelbourne/Arduino_STM32/blob/master/STM32F1/variants/nucleo_f103rb/infos_pdf/Nucleo_F103RB_hardware_preparation.pdf|Nicleo F103RB hardware preparation PDF]]
- "Desolder the 0-Ohm-resistors on SB55 and SB54 (bottom right) to cut the trace. Solder a little bridge on: SB16(MCO) (top left) and SB50 (bottom middle)"
dyld: Library not loaded: /usr/local/lib/libusb-1.0.0.dylib
"I got past the libusb issue with an OSX package here: http://rudix.org/packages/libusb.html"
SPI_2
it is possible to use 2 SPI ports: Using the first SPI port (SPI_1) SS <--> PA4 <--> BOARD_SPI1_NSS_PIN SCK <--> PA5 <--> BOARD_SPI1_SCK_PIN MISO <--> PA6 <--> BOARD_SPI1_MISO_PIN MOSI <--> PA7 <--> BOARD_SPI1_MOSI_PIN
Using the second SPI port (SPI_2)
SS <--> PB12 <--> BOARD_SPI2_NSS_PIN
SCK <--> PB13 <--> BOARD_SPI2_SCK_PIN
MISO <--> PB14 <--> BOARD_SPI2_MISO_PIN
MOSI <--> PB15 <--> BOARD_SPI2_MOSI_PIN